Christmas, Crafts, Home Decor, Winter

DIY Stenciled Reindeer Burlap Table Runner

Crafting a DIY Stenciled Reindeer Burlap Table Runner is the perfect touch to your Christmas decor repertoire. All you need is a length of burlap from your craft store, 1 or 2 Reindeer craft stencils by My Crafty Stencils, and the tools below.

In this tutorial we used:

Reindeer Craft Stencil – https://bit.ly/2OyhZuV

Stencil Brush – https://bit.ly/2F8va61

Repositionable Spray Adhesive – https://bit.ly/2yFQoBK

Frog Tape Painter’s Tape – https://bit.ly/2OtyDkb

Self-Healing Cutting Mat – https://bit.ly/2zC1Df4

Americana Acrylic Paint – https://bit.ly/2F9zNNt

Americana Matte Finish Acrylic Sealer – https://bit.ly/2PG5lyv

This slideshow requires JavaScript.

Burlap can but a bit unruly when it comes right off the bolt so expect it to be somewhat wrinkled. These wrinkles will come right out with the highest heat and steam settings on your iron. Start by figuring out how long you want your runner to be either by measuring or eyeballing it. Once you know your dimensions it is time to start the tricky part. Burlap is a woven material making it somewhat easy to unravel. This makes it a tricky material to use if not treated to prevent fraying over time. We will show you how to keep your burlap from fraying at the end but for now we want to take advantage of the fray. Identify the strand that you wish to cut along then work it out of the weave by snipping and teasing out the length of fiber. Once you have removed a single strand, cut along where the fiber you removed was. After this point you must be careful not to unravel your material along the edges as you stencil.

This slideshow requires JavaScript.

Once you have cut out a nice rectangular section of the burlap for your runner you should get it into position to stencil. Do this by folding the length of the runner in half to find the middle line. On either side of the center line we will be stenciling our first two repeats with the same stencil. You will space them out equal distance from each other along the center line. Use Spray Repositionable Adhesive on the back of your stencil then give it 30-60 seconds to become tacky before pressing it in place on the surface of the burlap. We slipped a Self-Healing Cutting Mat that had been coated in Spray Repositionable Adhesive to keep the burlap from sliding as you stencil but to also prevent paint from going through the burlap to the other side of the runner. You could also spray a piece of cardboard to keep the burlap still as you stencil without letting the paint seep. Before getting your paint ready, use Frog Tape Painter’s Tape around the edges of the stencil to keep paint from going over the edges of the stencil.

This slideshow requires JavaScript.

For this project we used Americana Acrylic Paint. We used Burnt Umber brown for the Reindeer and Titanium White for the falling snow. For smaller craft stencils you want to be sure that the stencil brush you get is not too big for the design. We used a 1/2″ stencil brush which is pretty much the largest brush I could use for a project this size. Swirl the stencil brush into your paint, then swirl the excess paint off in order to appropriately use the dry brush technique. Stenciling onto fabrics can be more forgiving than stenciling onto a flat surface in terms of paint build & bleeding but these mess-ups can still happen. To prevent this you must be sure that your stencil brush does not feel wet to the touch before swirling paint into your design. Rather than use several repeats, we swirled our dry stencil brush through the design until we achieved full coverage. You may wish to stencil a second coat onto the design after the first for maximum color. After stenciling the reindeer fully we prepared a second stencil brush with Americana Titanium White paint, swirled off the excess, then swirled through each snowflake onto the burlap. Be careful not to accidentally swirl white onto your reindeer or brown into your snow.

This slideshow requires JavaScript.

Now it’s time to break out the ruler. Flip to the other half of your runner then measure how far apart they will be spaced. We went with 6 centimeters apart per repeat. Rather than measure from the edge of the stencil we chose to measure between two elements of the design. Space the stencil apart six centimeters then repeat the design. For the rest of the runner we will continue spacing our reindeer six centimeters apart. We want our reindeer to face different directions. While you can measure and leave space to clean your stencil to paint the opposite side, for the interest of time we chose to use a second reindeer craft stencil to stencil the reverse of the design. Use Spray Repositionable Adhesive on the back of your second stencil, measure the design 6 centimeters from the last position, and paint the design.

This slideshow requires JavaScript.

For this project we stenciled 14 repeats of this stencil up and down our stenciled burlap table runner. Be sure that each time you move the stencil to the next position that you are moving the craft mat or cardboard beneath it as well. You don’t want paint seeping through the burlap to the other half of your craft. Once you have completed your repeats, spray the edges & surface of the runner with a couple of coats of Americana Acrylic Spray Sealant. This Acrylics Craft finish will keep the edges of your burlap table runner from fraying. Be sure to use your Americana Acrylic Craft Sealant in a well ventilated area. Now your craft is ready to dress up your table for the Christmas Season!

Outrobro

Thanks for checking out this tutorial! Be sure to subscribe and like for more My Crafty Stencil tutorials. For more information please visit https://www.mycraftystencils.com/ and check out the video below!

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s